咨询热线:

0531-88771136

您的当前位置: 首页 > 新闻中心 > 正文

保持机床精度的方法有哪些呢?

来源:http://www.jnhjgs.cn     发布时间:2020-05-12 08:50:40    点击:

保持机床精度的办法
Ways to keep the accuracy of machine tools
机床精度坚持办法不少,可是很少有人按照规范去操作,比如开机前的准备作业、操作中的留意事项、开机加工结束之后的保养、定时对机床进行检测、及时替换优质的配件、上适宜的光滑油、电脑体系更新与操作软件的维护、乃至是细节到操作环境的温度和湿度都是有规范可查的。
There are many ways to adhere to the accuracy of machine tools, but few people operate in accordance with the specifications, such as the preparation before start-up, precautions during operation, maintenance after start-up processing, regular detection of machine tools, timely replacement of high-quality accessories, appropriate smooth oil, computer system update and maintenance of operating software, and even the temperature and humidity from details to operating environment There are norms to check.
1,开机后,必须先预热10分钟左右再进行加工。长时间未使用的机床应该延长预热时间。
1. After the machine is started, it must be preheated for about 10 minutes before processing. Long time unused machine tool should extend warm-up time.
2,查看油路是否疏通。
2. Check whether the oil circuit is unblocked.
3,关机前将作业台,鞍座置于机器方位,移动三轴行程至各轴行程中间方位。
3. Before shutting down the machine, place the workbench and saddle in the central position of the machine, and move the three-axis travel to the middle position of each axis travel.
4,机床坚持干燥清洁。
4. Keep the machine dry and clean.
5,留意查看电器柜中冷却电扇是否作业正常,风道过滤网有无阻塞,清洗沾附的尘土。
5. Check whether the cooling fan in the electrical cabinet works normally, whether the air duct filter screen is blocked, and clean the dust.
6,每天做好各导轨面的清洁光滑,有主动光滑体系的机床要定时查看、清洗主动光滑体系,查看油量,及时增加光滑油,查看油泵是否定时启动打油及停止。
6. Clean and smooth each guide rail surface every day. For machines with active smooth system, check and clean the active smooth system regularly, check the oil volume, increase the smooth oil in time, and check whether the oil pump starts and stops regularly.
7,留意查看机床液压体系油箱油泵有无反常噪声,作业油面高度是否适宜,压力表指示是否正常,管路及各接头有无泄露。
7. Pay attention to check whether there is abnormal noise in the oil pump of the hydraulic system of the machine tool, whether the height of the working oil level is appropriate, whether the indication of the pressure gauge is normal, and whether there is leakage in the pipeline and joints.
8,留意查看导轨镶条松紧程度,调节间隙。
8. Check the tightness of guide rail insert strip and adjust the clearance.
9,留意查看主轴驱动皮带,调整松紧程度。
9. Pay attention to check the main shaft drive belt and adjust the tightness.
10,留意查看各运动部件的机械精度,削减形状和方位误差。
10. Pay attention to check the mechanical accuracy of each moving part to reduce the shape and orientation error.
以上就是保持机床精度方法的详细介绍,想要了解更多请点击官网http://www.jnhjgs.cn
 
The above is a detailed introduction to the method of maintaining the accuracy of machine tools. For more information, please click http://www.jnhjgs.cn
联系我们 contact

山东济南beplay全站app安卓_铝合金压铸厂-济南宏捷beplay全站app安卓有限公司

电话1:13173017488

电话2:18615459955

传真:0531-88771136

邮箱:hlm369@126.com

地址:山东省济南市大桥镇大王村北跨商务中心后三层白楼

山东济南beplay全站app安卓_铝合金压铸厂-济南宏捷beplay全站app安卓有限公司 手机: 13173017488 咨询热线: 0531-88771136 咨询热线:18615459955 邮箱:hlm369@126.com

公司地址: 山东省济南市大桥镇大王村北跨商务中心后三层白楼